Raynor Garage Door Torsion Spring Replacement Kit comes w/ Cones, and Winding Bars
Get Answers to Your Questions
Additional Details about:
If your spring is over 39" please call us to get a quote as that is a special order size. 800-783-6112. Our springs include cones installed on the springs. Enter the exact spring size you currently have. DO NOT CHANGE YOUR SPRING SIZE thinking you will improve operation NOTE: WHEN YOU SELECT LONG LIFE CYCLE SPRINGS THE SPRINGS THAT WILL ARRIVE ARE DIFFERENT IN SIZE BUT OPERATE THE EXACT SAME AS YOUR ORGINALS - DO NOT ATTEMPT TO MAKE THE CALCULATIONS YOURSELF! IF YOU ORDER 1-19/32" ID THE SPRING. THEY DO NOT COME WITH THE CONES. YOU HAVE TO REUSE YOUR OLD CONES AND THIS MEANS THAT YOU HAVE A CRAWFORD DOOR SPRING. THESE ARE VERY UNCOMMON SO BE SURE TO DOUBLE CHECK YOUR MEASUREMENTS
Did you know that you can actually replace your Raynor garage door springs yourself? Using your Raynor garage door parts manual as a guide, it’s easy to get the job done when you order this garage door torsion spring kit. We have all of the types of springs for garage doors that you might need. Just measure your current garage door springs and we’ll deliver the exact products you need to get your garage door working like new again.
If you have any questions about this great Raynor product, please utilize our “Questions” app below.
We always recommend replacing your garage door springs in pairs on doors with two springs. The reason is that springs are designed to open and close the door a predetermined number of times. So, if one spring broke, the other spring is going to, too.
Includes cones and winding bars for quick and easy replacement
Created specifically for Raynor garage door springs
Available in wire sizes and inside diameter sizes measured to the nearest 1/16th inch
Order custom spring lengths to fit your doors
Choose from left- or right-wound springs for a proper fit
You need four measurements to purchase the correct Raynor replacement torsion spring:
#1 Wire Size
#2 Inside Diameter
#3 Length of spring
#4 Wind of spring (Right or left wound)
A spring’s wire size can be determined by several different tools or techniques. Use of a caliper, micrometer, or wire gauge are common ways to determine a spring’s wire size. If none of these tools are available, simply measure ten coils of wire to the nearest 1/16th of an inch, and refer to the Spring Wire Chart. The spring must be tightly compressed, with no gaps. It’s also a good idea to measure twenty coils as a double check.
Measure the inside diameter to the nearest 1/16th of an inch. In most cases, the cones inserted in each end of the spring will have a manufacturers name Raynor which will give a clue toward the proper identity. The chart on the right shows common ID’s used by various manufacturers. If no manufacturers name is evident, usually a part number on the cone will indicate the inside diameter: 134 or 175 = 1 3/4" ID 258 or 263 = 2 5/8" ID 375 or 334 = 3 3/4" ID
LENGTH OF SPRING:
Measure spring length with the spring in its unwound state. In the case of a distorted or broken spring, simply count the total number of coils and multiply by the wire size. 120 coils x .250 wire = 30" 120 coils x .375 wire = 45"
RIGHT OR LEFT HAND WOUND:
To ensure the correct wind, please refer to the Winding Chart below. Please remember the side of the door a spring is located on does not indicate the wind of the spring. Most winding cones are color coded for hand identification. Right hand wound springs should have red winding cones. Left hand wound springs should have black winding cones.
LEFT WOUND SPRING AND RIGHT WOUND SPRING RESPECTIVELY
For a complete list of our Raynor Products
For other type and sizes of garage Door Springs Click Here
For more product & how-to videos subscribe to our YouTube channel:
QUESTION: My old spring measures 32 1/2 " . I ordered that but when it came it was 37". The paper work said 32.5 37". Is this correct? by Chris S 5/28/2017
STAFF ANSWER: You upgraded your spring to the long life cycle it will work 100% by Taylor M a
QUESTION: I have a 110 pound spring, can I replace a 165 pound spring with my 110 pound spring and leave the 165 pound one on the other side? by None N 7/4/2016
ANSWER: I think it's best to just replace both with brand new 165 pound springs. It will save you both time and effort. If you replace one side with a 110 pound spring it might break because you're letting a 110 pound spring do the work intended for a 165 pound spring. At the same time, the 110 pound spring is paired with an old 165 pound spring. Eventually, you will have to redo everything. My advice, just replace both sides with the recommended springs. These are jobs that need to be done right the first time. It will save you time, money, effort and avoid headache. by Rizaldy C a
ANSWER: No way! You must replace your spring with an EXACT replacement wind direction, wire size, length etc.. Watch some videos to see what is involved, it can be VERY dangerous as spring is under high tension. by Joseph N a
QUESTION: I am replacing the springs on a 40 yr old 18x7 wooden door . It has Overhead Door brand winding cones with the number 5005 no other numbers seen . What inner diameter spring do I order ? by paul p 2/25/2016
STAFF ANSWER: You will have to follow our product description on our website. by Taylor M a
QUESTION: Which end view is used to determine left or right wind of torsion spring? They're opposites, depending on end-view. by David F 12/11/2015
STAFF ANSWER: Please view our diagrams in the descriptions by Taylor M a