Are you constantly looking for new ways to make your shop or garage safe? North Shore Commercial Door has found one of the safest, quietest, smallest side mount DC operators in the industry today. The Zap DC garage door operator is your answer. The Zap features SafetySense technology, which is one of the industry’s most advanced obstruction detection systems available allowing the Zap to detect an obstruction on any part of the door, whether it’s opening or closing. This means a safe garage door operator not only for you, but for your door and its surroundings.
The Model 8825-3 is a medium duty commercial model operator with a 1HP motor. This operator is capable of running sectional overhead garage doors up to 240 square feet in size, 1200 lbs. in balanced weight, and able to customize with track configurations such as low headroom, standard lift, high lift, and full vertical lift. Like all the Zap model operators, the motor assembly only contains the motor, two pulleys and one belt, which means no chains or sprockets making all that unnecessary noise in your garage or shop.
The model 8825-3 only requires 7” of side clearance and 3 ˝” above the center of your spring shaft, so limited space is not an issue. The entire operator is NEMA 4 rated for water/moisture resistance. The 8825-3 offers many built in program features that are standard. These include auto close timer, cycle counter, and service due reminder.
You can also incorporate a multitude of auxiliary items to the Zap 8825-3. These include, but are not limited to interior/exterior lighting, additional wall controls, swipe card devices, dock equipment, motion sensors, and alarm systems. The list goes on and on.
Installation of the model 8825-3 is as simple as it gets. It only requires one person with a ladder to install the motor assembly on the spring shaft. Nothing mounts to the wall, jamb, or header area. Unlike traditional operators, you won’t be needing the scissors lift, two people, or a welder for this installation. The Zap control box is even easier to install. Just four screws to fasten it to the wall near the door, and power it up by plugging it into a nearby outlet in your garage or shop (electrical pigtail required). Now it’s just a matter of running the door open and close two times with the 8825-3 and it will set it’s fully open and closed positions for you. You just stand back and watch!
We are very impressed with the quality and capabilities of the Zap 8825-3 DC model operator and know you will be too.
Part Number: 8825-3
Medium duty commercial model operator
Safe, quiet & small
Compatible door sizes: Up to 240 sq. ft./1200 lbs.
Contains the motor, two pulleys & one belt
Requires 7” side clearance & 3 ˝” clearance above center spring shaft
Program features include auto close timer, cycle counter and service due reminder
Auxiliary capabilities include interior/exterior lighting, wall controls, swipe card devices, dock equipment, motion sensors, alarm systems & more
Simple installation of motor assembly to spring shaft
Control box fastens to the wall near the door & plug into outlet (electrical pigtail required)
Set fully open and closed positions by running the door open and close two times
Controller case rating: NEMA 4X/IP66
Controller dimensions: 8.7” H x 10.6” W x 4.5” D
Single phase voltage: 115 V US, 208-230V US, 208-230V EU
Amp draw: 3.2A
Control circuit voltage: 6VDC
Power rating: 1300 Newtons Equiv. 1 HP
Operator Motor Head Rating: NEMA 4*
Motor type: DC Gear Reduced
Motor cover dimensions:
Motor Voltage: 48-54 VDC
Limits determination: Physical/Self Calibrating
Duty cycle rating: Continuous
Operating temp range: -22 deg F to 212 deg F
Overload protection: Inherent motor current sensing
Torsion shaft type required: Solid w/keyway or hollow tube
Fits torsion shafts diameter:1”
Torsion shaft length required: 4.5” beyond outer edge of track
Side clearance required: 5” min for motor only
Side clearance required: 7” with motor cover applied
QUESTION: does the zap 8825 come with a remote control? by art m 9/7/2017
STAFF ANSWER: No it does not I would recommend are RC-1 kit to pair with this opener. by Taylor M a
QUESTION: I have a roll up door the shaft is EMT with no keyway cut in it will it work with a zap -825-3-c ? by None N 6/8/2017
STAFF ANSWER: These openers will not work on a roll up door. by Taylor M a
QUESTION: Do they make a smaller or lighter version my door is not very heavy? by Johnie N 4/9/2017
ANSWER: this is a small unit which works very well. by Dennis M a
ANSWER: Yes, the ZAP 825 Series 3 is lighter duty commercial version. They also make a residential version, the ZAP 8825-R4. However, the capacity of that motor is similar to that of the 8825 Series 3. by Richard G a
ANSWER: Yes they do.check the web site my opener is not very large and so far works great . And my 8x9 garage door is not heavy at all. Used on loading dock door. by art r a
QUESTION: Is the 8800-3-PB Series 3 Controller included in the $495 price for Item# 8825-3? by None N 1/17/2017