USAutomatic

USAutomatic 030212 LCR 4-Button Remote Control

This item is discontinued. Please view this replacement item:

MSRP: $26.84
$22.37
(You save $4.47 )
  • Shipping Cost? For the cost of shipping your item please add the item into the shopping cart. Once the part is in the cart fill out address information in the cart under the Shipping area in the Summary section. Our system will then calculate the shipping fee based on your location and the weight of the product. This is all done before you are asked to provide payment information.
North Shore Commercial Door now has the 4-Button Remote available for a low price. This Remote Control works with Ranger, and Patriot gate openers and receivers. Our Location is now fully supplied, and we are ready to get these products on the way to our customers! This neat little transmitter is slim and compact, and fits perfectly on your visor. This product (part #030212) comes equipped with a an alkaline battery, visor clip, and programming instructions to make your lives easier. Thanks to the awesome engineering of this product, the transmitter uses a frequency of 433.92 MHZ. This frequency is meant to control automatic opening systems and anti-burglar systems. Programming this product uses a set of nine, three position dip-switches, which results in up to 19,683 possible security codes. It’s easy to call this remote high quality when it boasts a range of 50-300 feet. Product Highlights
• Part number 030212 • 19,683 Possible combinations • 2 year limited warranty • Operate gate or garage with compatible 433 MHz receiver • Range of 50 to 300 ft typically • Comes with Visor Clip, battery, and instructions. Transmitter Setup:
(It is recommended that the dipswitch code be changed from the default factory setting)
1. Open the battery compartment door and locate the dipswitches.
2. Change the dipswitches to the settings you prefer, record for future reference
3. Transmitter Left Button to Receiver Programming: (standard Open/Stop/Close function)
4. Press and hold the left transmitter button down. Red light on transmitter should be on.
5. On the receiver, push the P1 push-button until the green LD light comes on.
6. Release both buttons. Transmitter left button to receiver programming is complete.
Transmitter Right Button to Receiver Programming: (Hold-Gate-Open) (Only if auto close timer is enabled)
1. The 2-channel receiver allows for programming the P2 relay from momentary mode (default) to latching mode. Transmitter right button can be programmed to hold gate open, over-riding the auto-close feature if activated.
2. Press and hold the right transmitter button down. Red light on transmitter should be on.
3. Press the P2 push-button until the green LD light comes on.
4. Release both buttons. Transmitter right button to receiver programming is complete.
Receiver Programming: Relay P2 programming from momentary to latching mode (to hold gate open)
1. Press the P2 push-button until the green LD light comes on, then release. Green LD light should be steady.
2. While the green LD light is on, push the P1 push-button down and release. Green LD light should be flashing. Latching mode is set.
Verifying Receiver P2 relay is programmed to latching mode:
1. Press the P2 push-button until the green LD light comes on, then release.
2. Green LD light should be flashing. If green LD light is steady, redo the Receiver Programming section above.
Resetting receiver P2 relay to momentary mode:
1. Press the P2 push-button until the green LD light comes on, then release. Green LD light should be flashing.
2. While the LD light is flashing, push the P1 push-button down and release. Green LD light should be steady. Momentary mode is set.
Erasing Single Transmitter from Receiver Memory:
The dipswitch settings of the transmitter to be deleted must be known. If known follow the steps below.
1. Set the dipswitches in a transmitter to match the switch settings of the transmitter code to delete.
2. Press and hold the left transmitter button.
3. On the receiver, push the P1 push-button until the green LD light comes on. Then release both.
4. Press and hold the right transmitter button.
5. On the receiver, push the P2 push-button until the green LD light comes on. Then release both.
6. Transmitter is now erased from receiver memory.
Erasing all Transmitters from Receiver Memory:
1. Press the P2 button on the receiver until the green LD light comes on. Then release P2 button.
2. While LD light is on press the P1 and P2 buttons simultaneously and hold until the green LD light begins to blink slowly. It should blink 4 times then all transmitter codes are erased.
If you have any questions or concerns please feel free to give us a call at 800 783 6112